Tag Archives: wind turbine installation

Friday 8th August 2014 – WOW!

What a storm!

It was totally stonishing. About 8mm of rain fell in about 30 minutes round about 22:30. It’s a long time since I’ve seen anything quite like it. I even had to close the roof windows as it was pouring in on me where I was sitting, and that’s not supposed to happen.

Mind you, it had been brewing all day. When the boulangère came by this morning, she mentioned that there might be a storm a little later. And it wasn’t long after that that we had the fist lightning flashes. They kept it up from about 12:00 until about 15:30 so I was pretty reluctant to go up on the scaffolding during that period, otherwise it would have been me frying tonight. That’s the one disadvantage of having metal planks.

When i considered it safe to do so, I went up there. Well, not quite – I had to round up all of the tools and fittings that I needed for the job. And that took several attempts to make sure that i had everything up there that I wanted. I drilled the hole, a 16mm hole, with the Hitachi battery-powered SDS drill and that went into the stone like a knife through butter. It’s a shame that the batteries are becoming tired in it now, because it really is one of the most useful tools that I have around here. I must sort out some new batteries for it.

Fitting my home-made eye wall anchor was straightforward – with a little persuasion from a hammer it went into the hole that I had drilled, but tightening it up was something else. With a little too much force, I reckon, I sheared off the wedge that splits the interior of the anchor. Then of course I couldn’t extract the broken one, and so I had to drill another hole and start again. This time I didn’t use quite so much force when tightening it, so I managed not to break it.

Fitting the turnbuckle was straightforward, but then actually fastening the guy wire was almost impossible as the length of the turnbuckle put it too far away from the scaffolding for me to reach it properly. I was lucky that the wire was quite long, as I was able to put a loop in the far end, pass the wire around the hook on the turnbuckle and then around a pivot (the framework upon which the wind turbine is mounted) and with a rope in the loop that I made, pull it back towards me again.

With it securely tied around the scaffolding, I could perform a major feat of gymnastics, balanced right on the edge of the scaffolding on the toes of one foot, and reach right out to the wire to fasten the wire rope ties (three of them) to hold the wire together.

Then dismantling the temporary fittings that I had made, I could tighten up the turnbuckle. And to my surprise, it pulled the wind turbine perfectly vertical instead of leaning over about 5° to the north.

All of this took me until about 18:20 and so for the remaining 40 minutes I did some (but not much) weeding in the vegetable plots. And as I knocked off, it started to rain. “Perfect timing!” I said to myself. And then we got the lot a few hours later.

i’m glad that I’ve fastened the wind turbine with a second guy wire. With just one, it was pulling it out of the vertical and of course, one isn’t very secure. Ideally it needs four and while I can think of a way to do the third one (and i might even do it some day) the fourth will be difficult. Nevertheless, progress has been made.

On Monday, I’ll start to attack all of the rest of the jobs that need to be done while I’m up there. Let’s see how long it takes me to finish them.

-1

Thursday 24th July 2014 – SO DESPITE THE LATE NIGHT …

… last night, I was still up at something like the correct time. And we had the usual procedure this morning of breakfast and then work on my website until midday. It was interrupted by a phone call from Rosemary – it’s nice to have phone calls from friends.

When I went outside, I went up onto the scaffolding in the beautiful weather and sloshed a pile of wood preservative onto the wood in the roof – the bits where I did the first coat yesterday.

While I was up on the scaffolding I untangled the mooring wires for the wind turbine. There’s only one attached to the wall at the moment and over the passage of time the other three have become tangled. It was a complicated manoeuvre involving a 4-metre lath of wood and a garden rake.

kwikstage scaffolding rear of house les guis virlet puy de dome franceThis afternoon I started checking over the rear wall of the house, slowly making my way down the scaffolding, dismantling it as I descended. I’ve arrived at the level of the roof of the lean-to and so I sloshed a pile of wood preservative on that too and I’ll do the second coat tomorrow.

I’m at the stage where I need a couple of buckets of mortar for the wall of the lean-to – some of the mortar that i did in the summer of 2012 needs some attention.

That’s tomorrow’s job and I finished off my working on the Sankey trailer. Of course, with it being ex-British-Army from the 1950S and 60s it’s a mixture of AF and Whitworth nuts and bolts. I have all my AF spanners but I’ve no idea where my Whitworth stuff is and so it wasn’t easy. I’ll have to use the angle grinder tomorrow on that. But the chassis isn’t as bad as I thought and even a manual wire brush cleaned it off quite well. I’ll still get the wire brush on the angle grinder to do it properly.

After knocking off, I watched The Spy Who Shagged Me, the same film that I tried to watch last night. And tonight I fell asleep in a different place and woke up in a different place too.

One day I might get to see all of it.

0

Monday 21st July 2014 – DURING THE NIGHT …

… we had 15mm of rain. No wonder I had difficulty sleeping and … errr … difficulty getting up this morning.

And if that isn’t enough, it’s carried on raining for most of the day and I shudder to think about how much rain there is the raingauge when I go downstairs in a few minutes to take the statistics… "20.5mm" – ed .

After breakfast I had an urgent letter to write and then spent the rest of the morning trying to make one of the three printers lying around here to work. To no effect whatsoever.

In the end, remembering that Cecile wanted me to check her post at La Batisse, I picked up her letters but at the same time printed off my letter. I could then send that off by recorded delivery at Pionsat.

plastic guttering les guis virlet puy de dome franceAfter lunch, I waited for the rain to subside and then went out to finish off the guttering. And it is finished too – at least as far as I can reach. And even though I say it myself, it looks as if it might even work. Tomorrow I’ll have to move the scaffolding round a little so that I can reach the rest of it.

I’ve also slackened off the cable that restrains the wind turbine against the wind. I’d tightened it up too tightly and it had bent the pole. Slackening it off a little put the pole more upright and even enables the wind turbine to pivot around better on its axis.

That all took until 19:20 when I knocked off and came up here where I crashed out for an hour or so. Tea tonight was a gigantic mushroom and lentil curry, seeing as how mushrooms were on special offer on Saturday at LIDL in Commentry. That will keep me going for three or four days.

0

Thursday 10th April 2014 – WHAT A WAY …

… to finish the day. At knocking-off time, the temperature in the verandah was still at 24°C and the water temperature was at 68°C. That can only mean one thing – a nice hot (water-cooled) shower. and it was gorgeous too.

Follow that up with a good shave and now I’m fit for anything (well, almost).

I had a bad night’s sleep for some reason or other and Marianne put in an appearance too. I’ve been thinking about her a little just recently – it’s almost a year since she passed on – but I never expected her to arrive.

So after breakfast and the website I went outside in the gorgeous windy weather and attacked the garden again. I want to put another raised bed in – that’s my next trick – and it needs to be ready for when I sow the potatoes. But there’s loads of wood all over it from a tree that collapsed a couple of years ago and all of that needs moving.

But to do that, I have to clear out all of the brambles and weeds that have grown all over everything and that’s not easy at all. It’s taking quite a while to shift and there’s still a pile to go, but at least I’m not going to be short of wood this winter. The kindling bin is stacked to overflowing and I’m preparing another, and the pile of small wood has grown to more than what it was at the start of winter. Added to that, the pile of big wood has almost doubled in size, and there’s more still to come.

This afternoon, seeing as it was quite windy, I went round to see the farmer in Le Quartier who is having wind turbine issues. And I didn’t even need to leave Caliburn to see what the problem is.

The installation is a load of rubbish and the company that did it – that one in Montlucon that I showed you a while back and which has now (of course) closed down – should be thoroughly ashamed of itself.

The two houses are in a hollow sheltered from the wind on two sides. On the third side is a large tree at each house – in one case just 25 yards from the turbine, and on the fourth side are all of the farm outbuildings.

So on three sides there is no wind at all and on the fourth side is nothing but turbulence. And as the turbines are only a metre or two above the roof line (instead of a maximum of 12 metres off the ground as allowed by law), the friction of the ground on the wind will slow the wind right down.

Quite frankly, the installation is a disgrace.

To make matters worse, just 200 metres away is the crest of a hill that is on the farmer’s property. A pair of 12-metre masts on there with these wind turbines on top would provide enough power to light up the whole village.

To give you some idea, of the two wind turbines (installed since January 2013) one has produced 12.5 KW of electricity and the other 13.2 KW. And that’s from an installation that has cost €8,000 each.

–

-2

Friday 18th November 2011 – WHEN I TELL YOU …

… that I knocked off at 17:27 today, you will probably think something like “idle burger” or something like that.

But not a bit of it.

In fact, 17:27 was when I stopped for lunch.

installing wind turbine les guis virlet puy de dome francePutting this wind turbine was not as easy as you might think.

First thing was to solder two longer wires to the couple of inches that come out of the wind turbine. My soldering is total rubbish, and what didn’t help was that the heavy-duty soldering iron I bought from LIDL ages ago didn’t want to work properly.

After trying a couple of others, it was the ancient soldering iron that I had bought from Tandy (and that tells you how old it is) that did some kind of a job on the wiring.

installing wind turbine les guis virlet puy de dome franceCollecting all the tools, I then went off up the ladder to the top of the scaffolding (and you can see how high I was as well – right at the top and that was nerve-wracking) and that wasn’t easy either.

One of the more difficult issues was fitting the wind turbine through the hatch in the lean-to floor. I had to dismantle the blasted thing, carry it through and up the ladder and then reassemble it on top.

Passing the wire down the tube was something else as well. For some reason it didn’t want to go down and I had to spend an age persuading it.

installing wind turbine les guis virlet puy de dome franceFitting the wind turbine on the pole was exciting as well and it was quite a feat of balance to do that on a scaffolding like that.

I then had to fix the rudder back on the wind turbine but that was something of an issue as it seemed that the captive nut that holds the rudder on had sheared off. And so that meant climbing right up there, undoing the side of the turbine, and putting a nut and bolt in place.

It was at that moment that the wind sprang up, and if it wasn’t easy before, then trying to do this right up there with the thing swinging around and the blades going round like the clappers – that just made it worse.

But anyway it’s up there, and it’s all wired in as well. But I couldn’t solder up the wires which was annoying – not even the Tandy soldering iron would do that – and so I’ve had to use chocolate blocks for that and the sheath that I put over the conduit now won’t cover up the joints.

As you can tell, it wasn’t easy and it was no wonder that,having decided to work right through until I finished, it was so late when I came to a stop. And I wasn’t feeling like carrying on.

But anyway, having been hit in the face by the turning blades on occasions too numerous to count, I know that it works. It will be interesting to see what power it gives out. 

-2

Wednesday 16th November 2011 – I’VE MADE GREAT PROGRESS …

MOUNTING BRACKET WIND TURBINE les guis virlet puy de dome france… today with the mount for the wind turbine. You can’t see it easily on the pic – you need to look carefully and you will see above and below the window the horizontal beams that will stand the vertical pole the required distance off the wall.

And if you look behind the ladder you can see the vertical upright – to the left of the yellow scaffolding pole.

It’s about 1 metre above the roof line and so what I’ve done is to cut a 1-metre length of pipe and I’ll be fastening the wind turbine to that. I have a special jointing piece for scaffolding pipe and so I can fit the two pipes together. That will give me a 2-metre height and I’ll see if I can slide the whole lot even higher.

The pole slides down easily enough – I have the squidged right hand to prove that – and so it should move up easily, or at least comparatively easily if I can manage the weight because it’s going to be quite something, the weight of it all, and I need all of the height that I can get.

My revised arrangements for mounting it all worked a treat and to fasten the wall anchors into the wall securely I’ve been driving them into the wall using a little something that I invented, based on a heavy washer, a couple of 17mm nuts, a deep 17mm socket and a lump hammer and that works a treat.

Mind you, it was all awkward to manipulate because it was so heavy and I had to manoeuvre the pipe in in three planes.

And I’m disappointed with this so-called super cement stuff. It’s not as super as I was hoping it to be and certainly not as super as the stuff that Terry was showing me the other day

Another thing that I found out today to my chagrin was that standard sizes in French pipe are different from standard UK sizes. And that’s awkward because French sizes are larger than UK sizes and I have all UK fittings. I’ll have to sort out some more pipe next time I go back the the UK.

Tomorrow I’m not going to be here. I’m round at Terry’s helping him fit his new door and window.

0

Wednesday 24th November 2010 – WE HAD THE SECOND …

… snows of winter today.

A bit more than yesterday as well. And although it melted fairly rapidly we had quite a pasting early in the afternoon while I was on my way to Liz and Terry’s. That didn’t stay long either though but the temperature has now plummeted and I slid Caliburn on a patch of ice on the way home.

Winter is definitely here.

rutland WG 901 wind turbine attached to fence les guis virlet puy de dome franceI’ve finished off fitting the wind turbine to the fence and it’s now wired in. And of course we are never ever going to have a breath of wind ever again.

It’s a weird place to put the wind turbine that’s for sure but it’s destined to go on the end of the house once the pointing is finished. And in any case that alley between the house and the trees is something of a wind trap and it’s going to be interesting to see what we can produce from it.

Meanwhile, of course, the wind turbine is being “run-in” so it’s a good idea to mount it, especially seeing as how we haven’t had a drop of sun for about three days now.

home grown beetroot bottled les guis virlet puy de dome franceRound at Terry and Liz’s Liz showed me how to pickle my beetroot and I now have 5 jars of it simmering away. I also took along a few of my chilis to dry out but I seem to have forgotten them. I also gave Terry a hand to put up the scaffolding – he’s fitting windows into his barn roof and I have to sing for my supper.

Not that I’m complaining of course . We had an absolutely excellent stew with dumplings, complete with home-made bread.

Tomorrow if it’s fine I’ll pull up my onions and start to dry them. But if the weather is bad (and what are the odds on that?) I’ll work inside the house.

-2